Vu+
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Vu+ SOLO Boot Loader Updgrade

Discussion in 'Vu+ General HowTo & Guides' started by Mito, Dec 19, 2011.

  1. nunigaia

    nunigaia Moderator

    Messages:
    4,553
    No ... Not necesssary...
     
    altazia likes this.
  2. altazia

    altazia Vu+ Newbie

    Messages:
    19
    Thank you Nunigaia

    Good day

    Altazia
     
    nunigaia likes this.
  3. nunigaia

    nunigaia Moderator

    Messages:
    4,553
    Make attention to the firmware ( image ) you intend to put in your STB ... For SOLO SE V2, the firmware is not " SOLO FIRMWARE ", but " SOLO SE FIRMWARE ", or you can brick your STB.

    Have a nice day, too. :)

    best regards
    nunigaia
     
    altazia likes this.
  4. BajsK

    BajsK Vu+ Newbie

    Messages:
    1
    Thanks, super guide!
     
  5. QASEM125

    QASEM125 Vu+ Newbie

    Messages:
    2
    Guy i want some help i am upgrade the vu+solo and when he upgrade hes stop on red collor and he didnt show me any picture or voice i need help pls for information my device is chinese made in china he is not a native.
     
    Last edited by a moderator: Sep 9, 2016
  6. nunigaia

    nunigaia Moderator

    Messages:
    4,553
    First of all, next time, don´t write only in " Capital Letters ", because it's hard to read it.

    So, you are admiting that you own a clone Vuplus STB, unfortunately we don´t give support for clones.

    Please read the forum rules --> http://www.vuplus-community.net/rules.html

    " Clones are not welcome here "

    " Buy an original Vuplus STB "


    best regards
    nunigaia
     
    Aliraza63 likes this.
  7. Ev0

    Ev0 Administrator

    Messages:
    2,237
    No help, support or discussion about clones is welcome on this board.
     
    Aliraza63 and nunigaia like this.
  8. mp3catcher

    mp3catcher Vu+ Newbie

    Messages:
    1
    This is the most wonderful forum i have seen, Ev0 thanks 4 this.
     
  9. Tmendozario

    Tmendozario Vu+ Newbie

    Messages:
    1
    gracias por todo probare de cambiarle la imagen darle mas partido a mi deco
     
  10. Meir Kriheli

    Meir Kriheli Vu+ Newbie

    Messages:
    1
    I have solo with BH 1.7.8.
    I tried putting the files under usb folder: /vuplus/solo/[files]
    Nothing happens wit leds.
    When I power off and on again, it powers on regularly.
    No update is done and not led blinking.
    Same for the vu firmware from vuplus web site.
    fat32 of course...
    What do I miss here?
     
  11. amio76

    amio76 Vu+ Newbie

    Messages:
    7
    Hi

    i have trouble with stb vu plus solo HD
    i cannot install firmware above 2.1 ( openpli neither black hole)

    When i flash with openpli 2.1 , i cannot play any channel as loaded correctly my iptv playlist.

    can anyone help me ?
     
  12. nunigaia

    nunigaia Moderator

    Messages:
    4,553
    Can you please post some photos of your STB?

    Like this:

    1. Front
    2. Back
    3. Upper Cover
    Thanks, in advance.

    best regards
    nunigaia
     
  13. amio76

    amio76 Vu+ Newbie

    Messages:
    7

    Thanks for reply
    here some pics
     

    Attached Files:

  14. amio76

    amio76 Vu+ Newbie

    Messages:
    7

    You may be told me to do that to know if this stb is clone or original , i think original but not sure... i heard that clone do not accept blackhole firmware upper than 2.0....

    May you give me solution... i already gived up the fight ... :(
     
  15. nunigaia

    nunigaia Moderator

    Messages:
    4,553
    Thanks.

    It seems to me that your STB is original.

    Flash your STB first with bootloader cfe 2.0 .

    Check the first post on this section, you have there the information needed to flash the bootloader. --> http://www.vuplus-community.net/board/threads/vu-solo-boot-loader-updgrade.4358/

    Note: Don´t forget to remove all your USB devices attached to your STB, before proceed the flashing procedure. ( this includes: Usb Pen Drives, Usb Tuners, Usb HDD ... etc ).

    You can find too the same information howto do it, on official Vuplus Webpage at this link --> http://vuplus.com/board/boardView.php?idx=5&pagenum=2

    After flashing the new CFE 2.0 bootloader, try reflash your STB with a new image ( more recent one ):

    • BlackHole 3.0.5A
    • Open BlackHole 4.1.018

    best regards
    nunigaia
     
  16. Mick12334

    Mick12334 Moderator

    Messages:
    1,840
    Have you tried loading the original firmware, from vuplus?
    Code:
    http://code.vuplus.com/
     
  17. amio76

    amio76 Vu+ Newbie

    Messages:
    7
    hy,
    i already tried several image (original) , but no success. it seem that the device do not accept firmware over vers 3 ( openpli 3 , bh 3.....) i cannot install fir exemple openpli 4 . openatv 5.1


    any idea ?

    now i am on openpli 3. cannot upgrade ....
    thanks
     

Share This Page